游标卡尺盒注塑模具设计

文档编号:JX1507  文档字数:17023.页数:39 附任务书，开题报告，实习报告，外文翻译，CAD图，solidwork三维图，PPT

摘要
 模具是工业生产的基础工艺装备，是机械工业和高新技术产业的重要组成部分。注塑模具在模具领域中发展最快，应用最广泛，因此，研究注塑模具对了解塑料产品的生产过程和提高产品质量有很大意义。本文的课题是游标卡尺盒注塑模具设计，文中首先对注塑件进行结构、工艺分析，然后通过测绘确定出了塑件的零件图。在已知塑件材料为PP1340的情况下，确定了PP1340的收缩率、塑件的尺寸精度、塑件的表面质量及成型的工艺参数，最后根据这些参数确定了注塑机的类型。在模具设计过程中，首先对分型面及型腔的数目进行确定，选择模架后分别对浇注系统、浇口、导向定位机构、滑块、顶出系统、排气系统、冷却系统进行设计。模具的初步设计完成后，用Solid works软件中的塑料顾问分别对浇口位置、塑料填充、冷却质量、注塑压力等进行分析，来验证模具设计的要否所合理，从而完成模具的设计。
 
 关键词：塑料注塑模  塑件工艺分析  模具参数

　Abstract
 Mold is the basis for industrial production technology and equipment, and an important part of the machinery industry and high-tech industries. Injection mold is growing fastest and being most widely used in the mold areas. So studying the knowledge of injection mold is good to know more about the process of plastic products, and it also makes sense to improve the products quality. This article is about the injection mold design and this design is for a product of calipers box. Firstly, it produces the molding’s structure and technology, and then draw the detail drawing through mapping. In the case of knowing the mold material which is PP1340, the article makes sure of shrinkage, dimensional accuracy, surface quality and technological parameter of molding. At last, on the basis of those parameters choose a right injection molding machine. In the process of design, at first, it makes sure the numbers of molding sand and the location of parting surface. After choosing the mold base, start to design gating system、pouring gate、guide rail system、sliders、ejection system、exhaust system、cooling system. After finishing the first step of design, using plastic advisor of a part pro/engineer analyses gate location、molding filling、colling quality、injection pressure and so on to make sure the design is or not right. If everything is ok, then finish the design.
 
 
 Key word: plastic mold, technical analysis of molding, mold parameters

 目   录
1 引 言 1
2 注塑件的分析 2
 2.1 注塑件零件图 2
 2.2 塑件的工艺分析 2
 2.3 PP1340塑料的主要工艺性能 3
 2.4 PP1340的收缩率的确定 3
 2.5 塑件的体积与质量计算 4
 2.6 塑件的尺寸精度 4
3 注塑成型参数确定 8
 3.1注塑成型工艺过程 8
 3.2注塑机的选择 10
4 模具设计 13
 4.1 模具设计的流程 13
 4.2 分型面的确定及型腔数目的确定 14
 4.3浇注系统设计 15
 4.4.排气系统设计 19
 4.5 成型零件的设计与计算 19
 4.6. 温度调节系统的设计 24
5 注射机的校核 26
6 模具加工工艺流程 28
结论 30
参考文献 32
致谢 33
附录一  塑料制品的公差数值表 34
附录二  常用液压机的技术参数 35
附录三  部分国产常用注塑机的技术参数 36

相关论文